What is gain staging?

Definition of used audio terms

To understand the process in detail, we need to clarify a few terms so you know what each phrase means and represents.

• Gain
  The amplification of an audio signal. So, turning up the gain means increasing the amplification of the audio signal.
   
• Unity gain
  Unity gain means you have the same audio level in the input and output stages. So, your plugin or gear neither increases nor reduces the level. It keeps it the same.
   
• Noise floor
  The noise floor is mainly used for analog equipment. It means the minimum amount of noise that a particular piece of gear produces - its self-noise. One important thing to understand is that noise is accumulative. Every piece of gear, or every part of your signal chain, will add to the noise floor of your recording.
   
• Signal-to-noise ratio
  This ratio compares the level of signal to the level of noise. A high signal-to-noise ratio is better than a lower one.
   
• Headroom
  The headroom describes how much signal a piece of gear or plugin can handle before it starts to distort.
   
• Signal chain
  The signal chain describes your audio's path before it hits your DAW. You can see an example with a microphone below.

With audio, you always want to get it right at the source. You want your audio to sound as good as possible at the recording stage.
To maintain a great sound through your signal chain, gain staging is helpful and necessary.

If you properly gain stage, your signal will not clip; it will have the lowest noise possible while still having enough headroom to mix and master.

If you don't consider gain staging, the following problems could happen:

• You add more noise than necessary to your finished track.
• You discover that a signal is clipping somewhere in the middle of your signal chain, so you need to go back and adjust multiple things.
• Ultimately, you could lose time, efficiency, and audio quality.

Here is the “too long, didn’t read” version of gain staging for simple home recording with a mic or instrument and just an audio interface:

If you follow these 3 rules, you are good.

1. Play/sing the loudest part of your song
2. Set the gain so you get between -12 and -14 dBFS in your DAW
3. Make sure you never go above -10 dBFS

If you want to dive deeper and learn a bit more about gain staging, read on.

For this blog, we assume you will record digitally on your computer.
 
Gain staging starts at the beginning, at the source. It is the most essential part of your recording, so pay close attention to get it right.
You want to play/sing the loudest part of your music a few times and set the gain: 

• You should aim to hit a level of -12 to -14 dBFS in your DAW.
• You should always stay below -10 dBFS to avoid clipping and leave enough headroom.

If you are unsure about the exact level, use the metering in your DAW. It's okay if it's not exactly -14 dBFS. As long as you are below -10 dBFS and the levels sound good and loud enough to your ears, you should be OK. 

If you use more analog gear before your signal hits the DAW, like a compressor or mixer, adjust the gain of each stage in your signal chain accordingly. Try to hit the sweet spot of 0 dBVU with each analog stage and between -12 to -14 dBFS when it hits your DAW.
Ideally, each stage in your signal chain has the input signal at the same gain level as the output signal, so you have unity gain.

This process ensures you leave enough headroom to avoid clipping at all costs but still have a loud enough signal to keep your signal-to-noise ratio optimal.
This is what gain staging is all about.
 
Remember, each piece of equipment introduces noise into your signal.

Noise is accumulative, which means you want to ensure that each stage introduces as little noise as possible.

That is why gain staging is essential to get optimal recordings.

If you want to record without worrying about the right gain, you should get an audio interface with Autosetup.

Autosetup finds the correct gain for you each time, so you can focus on your performance and won't have to worry about the correct settings anymore.

Once the signal is inside your DAW, you should keep a few things in mind to make your life easier and keep your audio sounding great.
 
Ideally, each audio track is between -12 and -18 dBFS. This leaves enough headroom for mixing and mastering but is loud enough so you don't have to crank the gain at any point.
 
If you have to lower the gain of your tracks, try to do it with a plugin and not with your faders. Ideally, you start your mix with all faders at roughly the same level. This makes it easier to mix and is a good best practice.
 
Another helpful technique is to have unity gain with each of your plugins. It means that your input and output levels are the same. This makes it easier to judge if your plugin adjustments are improving the sound.

If a plugin makes your signal louder, your ears will always think it sounds better.

We hope that this blog helped you achieve better recordings and that you understand why gain staging is essential. If you have any questions, you can always reach out on social media or through email.
 
Make yourself heard.